Product
Contact us
Sales manager：Tom Zhan
Tel:+0086 13632658537
Skype: zxp94520181
Whatsapp :+86 13632658537
Wechat: zxp94520181
Email：tom.zhan@primeda-telecom.com
www.primeda-telecom.com
Analog Camera Converters
Analog Video over Fiber Converter
PMD-1V1D-ST-SM
This video over fiber optic system is used to send 1 channel of analog video through one optical fiber cable to remote display devices, with RS485 data which can control PTZ remotely ,ST optical fiber module. Singlemode fiber up to 20Km. compatible with multimode up to 500m.
Multmode version 0-1.5Km is optional, if need, contact us.
Support OEM/Custom made,Factory wholesale price.
Multmode version 0-1.5Km is optional, if need, contact us.
Support OEM/Custom made,Factory wholesale price.
Feature:
Video:
1. Video format compatible with PAL, NTSC, SECAM.
2. Video Input / Output Impedance: 75ohm (unbalanced);
3. Video Bandwidth :5Hz-10MHz;
4. Video voltage 1VP-P;
5. Video SNR ≥ 70dB;
6. Differential gain ≤ 0.7%;
7. Differential phase ≤ 0.7 °;
8. 8- bit linear PCM coding
9. Video Interface: BNC;
Data:
1.Type: RS-485 (2 wires, reverse direction).
2. Connector: industry terminal block.
3. Use for remote control PTZ.
General Index:
1. The usual time between failures (MTBF) greater than 100,000 hours.
2. Working voltage: AC100-240V, DC5V2A. ***US/EU/UK/AU standard plug is optional.****
3. Operating temperature: -40 +70 degree.
4. Operating humidity :0 -95 % non-condensing.
LED indicators:
P: power supply. always on after power-on, display red light. Blinking or not on is abnormal.
F(SYN): Fiber Synchronous light, always on when TX and RX work, display green light. If blinking or not on is abnormal, please check power supply and fiber optic connection status. Note: if fiber have big loss, no fiber signal pass through from TX to RX, the light is not on. Need to reduce fiber loss.
Note: GND must be grounded, in order to prevent lightning and prevent static electricity accumulation.
1. This video over fiber optic is used to send 1 channel of analog video signals through one optical cable to remote display devices. Optical interface: ST.
2. Applicable for Analog cameras, Compatible for PAL, NTSC, SECAM Video format automatically.
3. Suitable fiber type: universal multimode fiber. Long transmission distance up to 20Km by a singlemode fiber, and compatible with multimode fiber 0-500meters. With RS-485 data (reverse direction) for remote control PTZ.
4. LED indicators can dynamic feedback link connection state and fault detection to easily monitor network status.
4. LED indicators can dynamic feedback link connection state and fault detection to easily monitor network status.
5. Plug and Play, Cost-effective, Greatly save your engineering cabling cost.
Video:
1. Video format compatible with PAL, NTSC, SECAM.
2. Video Input / Output Impedance: 75ohm (unbalanced);
3. Video Bandwidth :5Hz-10MHz;
4. Video voltage 1VP-P;
5. Video SNR ≥ 70dB;
6. Differential gain ≤ 0.7%;
7. Differential phase ≤ 0.7 °;
8. 8- bit linear PCM coding
9. Video Interface: BNC;
Data:
1.Type: RS-485 (2 wires, reverse direction).
2. Connector: industry terminal block.
3. Use for remote control PTZ.
General Index:
1. The usual time between failures (MTBF) greater than 100,000 hours.
2. Working voltage: AC100-240V, DC5V2A. ***US/EU/UK/AU standard plug is optional.****
3. Operating temperature: -40 +70 degree.
4. Operating humidity :0 -95 % non-condensing.
LED indicators:
P: power supply. always on after power-on, display red light. Blinking or not on is abnormal.
F(SYN): Fiber Synchronous light, always on when TX and RX work, display green light. If blinking or not on is abnormal, please check power supply and fiber optic connection status. Note: if fiber have big loss, no fiber signal pass through from TX to RX, the light is not on. Need to reduce fiber loss.
Note: GND must be grounded, in order to prevent lightning and prevent static electricity accumulation.
- Online Service
-
